- INPA AIRBAG RESET HOW TO
- INPA AIRBAG RESET INSTALL
- INPA AIRBAG RESET DRIVER
- INPA AIRBAG RESET WINDOWS 10
- INPA AIRBAG RESET PC
I have checked the instrument cluster itself and didn't find any sign of specific action done. May be some smart guy made a trick to make the light dead instead of solving the problem with pretentioneers ? All other lights come on when I put the key on. I do not believe that it could be the burnt LED. What do you suggest to check further to find the reason of the problem.
INPA AIRBAG RESET PC
But the diode on the pc board of the cluster does not come on. The signal on this wire gets about 5V DC when I turn the key to on. I checked the wire from srs module to instrument cluster: it is OK. I put a plastic streaps into the slots to isolate the shorting contacts and now the srs module get proper resistance of the pretensioneers. The problem was that the pretentioneers plugs were disconnected by somebody and black protecting detailes were lost, so the srs module gave codes that there was short circuit in pretentioneers. There was an old problem with seat belts pretensioneers connection which was already solved and the srs ECU gives no codes now. The problem I have is concerned with the srs warning light which never comes on even when I turn the key to on position. If you can not find any problems there, you should really get an OBD2 scanner or let a workshop read the codes otherwise, you will just guess the problem out of the dark. Problem: When I connect cable to car red led is on but when I try to connect via Inpa (airbag) led goes out and message says cannot connect, with Ncsexpert led is on until I select CAS and then it immediately goes out and message Vin is faulty COAPI-2020: No answer from ECU IFH-0009: ECU not connected or doesn’t answer.
![inpa airbag reset inpa airbag reset](http://www.car-auto-repair.com/wp-content/uploads/2017/05/BMW-INPA-software-5.jpg)
Spray the connector plugs with an electronic cleaner and restart your car.
INPA AIRBAG RESET DRIVER
In some older cars, though, it is possible to reset the airbag light without a scanner by removing the car battery terminals.Ĭheck the wiring system underneath the driver or passenger seat for any loose wires or corrosion in the connector plug. Luckily, in many car models, the airbag light will also go away by itself if you have repaired the problem. This is for safety cautions because you should always repair the fault after the airbag light occurred. It is impossible in most car models to reset the airbag light without a scanner.
INPA AIRBAG RESET HOW TO
How to reset airbag light without a Scanner If the problem comes back, reread the codes and continue the procedure. If the airbag light is gone after a test drive, there is a big chance that the problem is solved. If the airbag light seems to have gone away from your dashboard – restart your ignition and go for a test drive.
![inpa airbag reset inpa airbag reset](https://i.ytimg.com/vi/MMmCxe76CkI/maxresdefault.jpg)
How to reset the airbag light with a scanner This gas floods the airbag and causes it to expand hence, protecting the driver from injuries by occupying the steering wheel and the side. Most airbags use sodium azide as the explosive element, and the gas produced can either be argon or nitrogen. This heating element promotes an explosion inside the airbag that rapidly generates a harmless gas. The airbag circuit has a heating element activated through an electric current. Note that the light will remain on for about seven seconds before turning off. After that, observe the airbag light turning on.
![inpa airbag reset inpa airbag reset](https://blog.uobdii.com/wp-content/uploads/2016/11/INPA-K-DCAN-BMW-E46-airbag-reset-DLC-port-2.jpg)
Put the car key into the ignition system, and then turn your car switch to an on position. When you hit something at high speed, your car will decelerate, and this will activate an accelerometer that triggers the airbag circuit. For you to reset the airbag with a scanner, you must take these steps: Step 1.
![inpa airbag reset inpa airbag reset](https://cdn.shopify.com/s/files/1/0072/5424/5449/products/bmw-inpa-k-can-1-5_1024x1024.jpg)
If you do not have an airbag, you could hit your head hard on the steering wheel or dashboard. So before we look at how to reset the airbag light , you should know how the whole function works.Īirbags are lifesavers when you are speeding and hit another car head-on or hit a stationary object.
INPA AIRBAG RESET INSTALL
Download and Install ODIS 5.How to reset airbag light without a Scanner How do airbags work?.